Model Range:
3 Cell 2 Volt 3 Cell 6 Volt 4 Cell 12 Volt 2 Cell 24 Volt

3 Cell Automatic Battery Charger
Model : ABC – X – 6V – 3B – YYYA - A

Features:

  • Suitable for charging 1 to 3 Nos. 6V Batteries Simultaneously. Very useful for ST Buses, Railway etc.

  • Highly efficient SMPS based design with constant voltage charging facility, protects Batteries / Cells from overcharging.

  • Fully protected against over voltage, short circuit, over temperature and Battery Reverse Connections.

  • Charging current limit Adj. pot provided to limit maximum charging current, to protect Battery / Cell from overheating.

 3 Cell 6V Battery Charger

Specification for 3 Cell Automatic Battery Charger
Model : ABC – X – 6V – 3B – YYYA - A

1.

Input Voltage

X

Nominal Input Voltage

Input Voltage Range

1

110 VAC Single Phase

90 – 132 VAC

2

230 VAC Single Phase

180 – 264 VAC

12

110/230 VAC Switchable Single Phase

90-132 / 180 - 264 VAC 

2.

Frequency

: 47-63 Hz

3.

Input

: Through 3 core cable and 15 A 3 pin plug provided on the side of   
Battery Charger.

4.

Battery Charger ON/OFF Switch

: 16 Amp rating Rocker Switch with Neon Indicating lamp Provided
on the Front Panel.

5.

Battery Charging Voltage

Sr.No

No. Cell

Nom. Voltage

Float Voltage
Adjustment Range

Boost Voltage
Adjustment Range

1

1 Cell

6V

6.25V – 7.0V

7.0V – 7.9V

2

2 Cell

12V

13.1V– 14.1V

14.1V – 15.1V

3

3 Cell

18V

19.9V– 20.9V

21.4V – 22.4V

6.

a. Charging Current
b. Code YYYA
c. Max Current @2V
d. Max Current @4V
e. Max Current @6V

70 Amps max.

100 Amps max.

135 Amps max.

165 Amps max.

70 A

100 A

135 A

165 A

70 A

100 A

135 A

165 A

35 A

55 A

70 A

82 A

23 A

36 A

45 A

55 A

7.

Charging Current

: Maximum charging current can be Adjusted  from 10 % to 100 % of 
Current rating with multiturn pot.  Maximum charging current limit
should be set as per battery capacity.

8.

Battery Switch

MCB 50A,
1 pole

MCB 40A,
2 pole

MCB 50A,
2 pole

MCB 63A,
2 pole

9.

Protections

: Battery Charger protected against Over Load, Short Circuit, Over Voltage,
Over Temperature & Reverse Input.

10.

Display
Voltmeter

Current Meter

3 ½ Digit DPM for displaying Battery / Charger Voltage (in Volts)
Accuracy 0.2V +/- 2 Digits

3 ½ Digit DPM for displaying charging current (in Amp).
Accuracy 0.2V +/- 2 Digits

11.

Battery Connector

TB56 Series 8 Position

Bus bar with 5/16” threaded STUD,  1 each for +ve & -ve

12.

Charging Stages

: Boost charge
: Float charge

13.

Indications

: Red LED for Boost stage
: Green LED for Float stage (Indicating   Battery  is fully charged )
: Red LED to indicate Reverse Battery Connection.

14.

Enclosure

: IP 20.

15.

Mounting

: Provision for Table top and wall / Panel mounting.

16.

Size

: 320(W) x 350(H) x 150(D) MM

17.

Weight

: 13 Kg.

Specifications subject to change without notice.

 TOP